There is no doubt that Whirlpool is one of the biggest names in appliances. While Whirlpool Cabrio washers are among the most popular models, they sometimes have problems. Sometimes Whirlpool Cabrio washer may suffer from problems, and we have listed multiple fixes below.

Despite the fact that this model has fewer problems than most, it still requires some common fixes from time to time.

Here’s a look at all the common problems with Whirlpool Cabrio washers and how to fix them.

 

How to fix a Whirlpool Cabrio washer that won’t spin

There is no doubt that the spin cycle is an important part of the washing process. Are you having problems spinning your Whirlpool Cabrio washer? Some of the most common problems you may encounter are:

 

Whirlpool Cabrio Washer Problems: Make sure the drive pulley nut is tight

The drive pulley can become loose over time if the nut holding it in place becomes loose.

When this happens, your Whirlpool Cabrio washer may stop spinning.

The drive pulley must be located and the nut tightened.

 

Whirlpool Cabrio Washer Problems: The shift actuator has failed due to a malfunction

In addition to having many moving parts, washers have to endure a large amount of weight on a daily basis.

Due to this, it means that the parts that are responsible for handling motion are susceptible to cracks and malfunctions as well.

If your Whirlpool Cabrio washer won’t spin and is displaying error codes like F7 or E1, you may have a malfunctioning shift actuator.

In this case, you will need to replace the part by following these steps:

1. Make sure all water lines are turned off and the machine is unplugged.

2. Reconnecting the machine’s water hoses should be done with the hot and cold hoses marked.

3. To prevent the drain line from pulling tight, remove it from the wall.

4. The washer should be placed on its front. To cushion it, place it on a thick towel.

5. Under the machine, you will find the part you need to access.

6. A top and bottom screw are required to remove the shield.

7. On the left, just below the shield, are the shift actuators.

8. The damaged part must be removed in order to be repaired. In order to hold the actuator in place, there are two screws. After unclipping the wire harness, place the old part to the side.

9. The part needs to be installed in order to be replaced. Using the wire harness, reassemble the machine by going backwards and connecting the wires.

 

There is a problem with the Whirlpool Cabrio washer not filling up

When your washer will not fill up with water, it can be extremely frustrating.

The following two items should be checked if you are experiencing this issue:

 

Inlet valve clogged up with debris

To begin with, you should check the water inlet hoses and screens to see if there are any clogs inside them.

It is through these inlet hoses that the main water supply is connected to your machine.

In order to prevent debris and sediment from entering your inlet valve, there are metal screens attached to both ends of the hoses.

Check this issue by turning off the water supply to your Whirlpool Cabrio washer.

After disconnecting the hoses from the faucet and washer, proceed to the next step.

Check the screens for debris and remove it if necessary. In case they are damaged, you should replace them as soon as possible.

Likewise, if debris has bypassed the screens and is present inside the inlet valve, you should inspect it.

The two ports on the valve should be cleaned in this case.

 

Water Inlet Valve Coils That Have Been Burned

In some cases, a burnt coil can cause the water inlet valve to malfunction.

The water inlet valves in your home are likely to be faulty if you have previously checked the water pressure and inlet hoses.

In the same way that most electrical components have a limited lifespan, coils in valves have a limited lifespan as well.

It is possible for them to become overworked and burned out over time.

This results in the gates of the valve being unable to open when electrical signals are sent to your washer.

Test continuity with a multimeter to determine if this is the issue and if you do not have one, you will need to replace the water inlet valve. In addition, the inlet valves of water supply systems are not designed to be repaired.

 

There are problems with the bearings on Whirlpool Cabrio washers

Your Whirlpool Cabrio washer may have a bearing problem if it is loud during the spin cycle and leaks water.

 

There is a leak in the seals on the bearings

This problem is most commonly caused by torn tub seals.

There is a risk that water will leak from the seal and make its way into the tub bearings as a result.

To prevent your bearings from failing, replace the tub seal and tub bearings immediately.

There is a lot of disassembling involved in this repair, so it is not for the faint-hearted.

 

Whirlpool Cabrio washer OL error code

The OL error code is one of the most common codes to appear on Whirlpool Cabrio washers.

There is basically an overload error in the code. As a result, sometimes it can be as simple as a machine that is overloaded.

If you are unable to clear this error code on your machine, check the following two parts:

 

A bearing is malfunctioning

A bad bearing prevents your tub from spinning freely, so you won’t be able to use it. In general, you’ll know the problem with your machine as soon as it roars loudly during a spin cycle.

In order to fix this problem, you will need to replace the bearing. Moreover, several tub seal bearing kits and bearing driver tools are required for the repair.

 

The motor’s direct drive nut is loose

If the nut on a direct drive motor becomes loose, an OL error code can appear:

1. It is recommended that the power cord be disconnected from the wall.

2. The water supply hoses should be disconnected from the machine’s rear and the water supply should be turned off.

3. To work comfortably, you should pull the washer away from the wall.

4. Loosen the screws holding the access panel in place and remove it.

5. The drive motor and belt should be located.

6. Tighten the motor’s mounting nut with an adjustable wrench and loosen it with a counterclockwise turn.

7. Turn your wrench clockwise while holding the motor firmly in place.

8. One finger should only be able to depress the belt about half an inch, so two people might be necessary.

9. The machine should be reassembled, the power restored, and the hoses reconnected.

 

Lock won’t stay on Whirlpool Cabrio washer

It is usually the lid lock of your Cabrio washer that won’t lock if your washer won’t lock. This part can be troubleshooted as follows:

 

The lid lock

There are a number of problems that can arise when using a direct drive washing machine and this is one of them.

There is a possibility that the lid lock switch of your Whirlpool Cabrio washer has failed if it fills with water but will not spin.

Moreover, the best way to diagnose the problem is to put the washer in a spin mode in order to see what is causing it. Additionally, using a screwdriver, insert a screwdriver into the hole where the lid switch actuator is located, and then open the lid.

If the washer starts running while you are doing this, but doesn’t start when you close the lid – then the switch is faulty. Indeed, if this test doesn’t produce a result, you may need to use a multimeter.

 

There is a problem draining the Whirlpool Cabrio washer

A Whirlpool Cabrio washer that won’t drain usually has a problem with the drain pump.

 

A faulty drain pump or one that is stuck

If your drain pump is faulty or stuck, follow these steps:

1. Make sure the drain pump receives voltage from the main board. Listen to the pump motor to see if it runs.

2. Make sure the connections at the pump are good and the wiring harness is not damaged if it won’t run.

3. There is probably a clog in the pump if voltage is going to it and you can hear it.

4. The hose connecting the tub to the pump should be removed. Make sure it is not blocked.

5. Clean the pump motor by removing it and inspecting it; a blocked pump motor will prevent the machine from draining.

6. Make sure the impeller inside the pump isn’t wobbling.

7. The hose should be disconnected from the pump if the washer fails to drain even after disconnection.

8. Ensure that this hose is free of debris and obstructions.

9. It is best to replace the drain pump motor if the pump is getting power and there are no clogs.

10. When you use a multimeter to check the continuity inside drain pumps, you can determine if the drain pump is malfunctioning.

 

The Whirlpool Cabrio washer stops in the middle of a cycle

Does your washer stop in the middle of a cycle? Is there an error code such as F1 or E2 displayed on Whirlpool Cabrio washer? However, if you do, you might be interested in these items:

 

The error code F1 or E2 has been encountered

This error code indicates a problem with the motor control circuit’s main control. Steps to be taken are as follows:

You should unplug the washing machine for at least five minutes before using it. Reconnect the board to see if it has been reset.

The error code may persist if the back panel is removed and the machine is unplugged again.

Wires must be insulated properly and be connected securely.

Moreover, make sure the wiring harness on the stator is connected correctly and has no damage to the wires.

The motor control circuit board needs to be replaced if all the wiring is in order.

In order to confirm this, some diagnostic steps will be required, as well as the washer’s wiring diagram.

There are many problems that Whirlpool Cabrio washer have, and we’ve explained how to fix them above.

Have you dealt with any other issues? How did you fix them? What were the issues?

Feel free to comment below and let us know what you think.

 

Read More: