It should be noted that an LG washer showing the UE error code signifies an uneven load inside the machine. It is typically feasible to solve the problem by adjusting the load or leveling the washer. In any case, if the problem continues, there may be a damaged part that needs to be replaced.

The LG washer displays the uE error code when it is trying to resolve the problem. In order to balance the load, the washer will fill up with water. The machine will then drain and try to spin again after draining. It is recommended that the washer repeats this process three times. The LG washer error code will switch from uE to UE if it can’t fix the problem, which means it needs help balancing the load.

The LG washer UE error code can be resolved by implementing the methods below.

 

Would it be conceivable to find a solution to the LG Washer UE Code Error?

1. To get rid of LG Washer UE error code, it is of utmost importance to make sure the load is balanced in the washer.

If necessary, add or remove items to prevent the washer from being overloaded. Balance the load if it appears unbalanced by adding or removing items. Unbalanced washers are caused by bulky or large items, such as pillows and blankets, or sometimes small loads. Consider adjusting the settings of the wash cycle or adding or removing items to fix the problem. Top-loader washers should be checked to make sure items aren’t tangled around the agitator.

 

2. The LG washer should be rinsed and spun.

You should empty the washer and run a rinse and spin cycle afterwards. It is expected to require approximately ten minutes for the cycle to complete. At the end of the cycle, check to see if the LG washer UE or UE error code is still displayed. In the event that the error code is present, you should move on to the next solution to troubleshoot the problem. If the error code no longer appears, balance future loads to prevent overloading the washer. You can also prevent the problem from occurring by making sure the washer is level.

 

3. The LG Washer UE error code can be corrected by ensuring that the washer is leveled.

By using a bubble level, you will be able to ensure that your washer is level. The level should be positioned across the width and from front to back. In case the washer’s legs aren’t level, you can adjust them. You can check the plastic guard around the drum on top-loading washers to make sure it is not more exposed on one side than on the other. You will need to adjust the legs if one side of the drum is leaning more than the other.

 

4. To fix LG Washer UE error code, align the legs to level the washer.

The bottom of most washers has four leveling legs to help level them. Locking nuts on the leveling legs can be adjusted by loosening them with a wrench. You can then lower or raise the leg by turning the leg clockwise or counterclockwise. Ensure that the washer is level by adjusting the legs. In order to ensure that the washer is level, tighten the locking nuts so that they are locked in place once you have verified that it is level.

 

5. The leveling legs of the washer should be checked.

It is also important to ensure that the leveling legs are firmly planted on the floor to provide stability when the washer spins. To prevent the washer from moving during the cycle, use non-skid pads if the floor is too slippery to keep it balanced. Also, the locking nuts that secure the legs in place must be tight against the washer’s base. Make sure the locking nuts are tightly secured with a wrench.

 

6. The Rotor Mounting Nut of the washer should be checked.

There’s a fix for the LG washer UE error code that’s not as common as the one above. Tighten the rotor mounting nut securing the rotor assembly to the stator if the problem persists. Also, you might want to check the bolts that are used to secure the stator to make sure they are tight. Additionally, replacing the bolts may fix the problem if they’re damaged. Before removing the panels to reach the stator assembly, make sure the washer is disconnected from the power source.

 

7. It is not a bad idea to check the washer’s suspension rods or shock absorbers.

A top-loader washer’s suspension rods and a front-loader washer’s shock absorbers reduce the washer’s movement. The LG washer UE error code indicates worn suspension rods or shock absorbers that need to be replaced. A worn suspension rod or shock absorber may cause excessive noise and vibration.

When removing the panels to access the suspension rods or shock absorbers, make sure the washer’s power source is disconnected. In addition, the suspension rods are attached to the outer tub and threaded through the brackets that support it. The cabinet and tub are connected by shock absorbers. Moreover, if you turn the washer on its side, you may be able to reach the shock absorbers at the bottom.

 

8. The hall sensor in the washer needs to be checked.

A hall sensor or rotor position sensor monitors motor operation. The UE error may be caused by a faulty hall sensor in some cases. Testing the hall sensor with a multimeter can determine if it needs to be replaced. Moreover, it is situated at the base of the stator where a hall sensor is positioned. Connect the washer to the power source before removing the panels to access the hall sensor.

 

9. Washer Control Board and Display Panel need to be replaced.

Replacement of the control board and the display may resolve the UE error code if you are still unable to resolve it. Fix this issue by assuming the washer’s control board has a fault that indicates an unbalanced washer.

 

10. The washer’s software needs to be upgraded.

It has been known that LG top-loader washers have had problems with the Smart Balance feature that caused the UE error code in the past. However, the problem can be fixed by contacting LG Product Support and requesting a software update.

 

Read More: