A glass top electric stove burner that is not working may seem like it needs to be fixed by a technician. In most cases, repairing a glass top electric stove burner that is not working is relatively simple. This guide and a Phillips-head bit are all you need, as well as a multimeter if you have one. Once you have identified the problem, you can buy a replacement part online and install it by simply plugging it in.

Please continue reading to identify the problem and fix your not working glass top electric stove burner.

HOW DOES THE GLASS TOP ELECTRIC BURNER WORK?

You can identify the cause of your glass top electric stove burner not working by learning how an electric stove burner operates.

120 volts of AC are sent through two legs connected to the burner when it is turned on, creating a closed circuit and heating the burner. The most common cause of an electric stove burner not heating is that the burner is unable to complete a closed circuit.

Multimeters can be used to test the burner’s terminals to see if the connector does not allow a closed circuit, also known as “no continuity”. There may also be a problem with the burner’s switch or wiring if there is no closed circuit.

HOW TO PREVENT THE GLASS TOP ELECTRIC BURNER FROM NOT WORKING?

The glass top of an electric stove burner might not be working because food, liquid, and grease can get through the cracks and damage the burner receptacle. Therefore, spills should be cleaned up immediately and the burner should be kept clean. It is also possible to cause a burner to fail when the burner coil is treated rough.

Glass top electric stove burner not working: Check for safety before troubleshooting.

Remove the power from the stove before troubleshooting the not working glass top electric stove burner. Water should also not come into contact on the stove’s electrical components.

AN ESSENTIAL GUIDE TO OPENING A CERAMIC COOKTOP (GLASS OR SMOOTH TOP STOVE).

For a closer look at the electrical components beneath a ceramic stove, you must unscrew the stovetop. Using a Phillips-head screwdriver or bit will likely be required to remove the stovetop. Under the part of the cooktop that extends toward you from the front, you usually find screws for the cooktop.

Lift the front of the stove at an angle of forty five to ninety degrees after removing the screws. You’ll probably need a sturdy object to support the stovetop while you check the electrical components.

After the stovetop is raised, you’ll need to unscrew two metal brackets that hold the burner coils in place.

WHAT IS THE EASIEST METHOD TO ACCESS A COIL TOP STOVE?

Some of the troubleshooting for a coil top stove can be done by lifting the burner coil up or removing it from the receptacle. You should keep the angle of the burner coil as low as possible when removing it from its receptacle. Unplugging it will require some elbow grease as well.

It is usually possible to access the electrical components beneath the stove by lifting up the stovetop at a forty five to ninety degree angle from the front. On most coil top stoves, you’ll have to hold up the stovetop while you troubleshoot the electric burner.

HOW TO FIX AN GLASS TOP ELECTRIC STOVE BURNER THAT IS NOT WORKING?

THE BURNER MUST BE DISCONNECTED.

There may be an improper connection between the receptacle and burner terminals if your glass top electric stove burner is not working. If the terminal is loose, you can test it by wiggling it, but it is better to unplug it first, check it for damage, and then reconnect it.

When plugging it in, make sure the connection is tight and the cable is not loose. There is a possibility that your glass top electric stove burner is not working if the terminal is damaged, so you should either replace the receptacle or the burner.

INSPECT THE BURNER RECEPTACLE FOR DAMAGES.

The burner receptacle can be damaged by food, liquid, or grease dripping down. There are times when the receptacle burns out and the voltage to the burner is affected.

Look for signs of burns or other damage on the receptacle. Receptacles with badly damaged contacts should be replaced.

Examine the burner coil to determine if it has been damaged.

You should be able to identify damaged or broken coils on coil-top stoves relatively easily. It is simply a matter of inspecting the coil for any breaks or blisters. As soon as the coil is cracked or damaged, it must be replaced or upgraded as soon as possible. Swap the suspect burner for another working burner if you’re unsure whether the coil is damaged. The burner coil will not be defective if it works when plugged into a different receptacle.

Check the ceramic stovetop coil for breaks or other damage once you have accessed it. It is imperative to replace the coil if it is broken.

Multimeters can also be used to check the burner’s continuity. If the probes of the multimeter don’t connect to the burner’s terminal, the burner needs to be replaced.

WIRING THAT IS BURNT OR LOOSE SHOULD BE CHECKED.

It is not uncommon for the wiring underneath the stove to become damaged at times. In order to check the wiring and connectors, you will need to lift up the stovetop. If the wiring or connectors are damaged, they will need to be replaced. If the glass top electric burner is not working, check the connectors for loose connections.

Check the burner stove switch for proper operation.

The glass top electric burner may not be working even if there is nothing wrong with the burner’s switch. The suspect burner should be replaced with a working burner in order to determine whether the switch is defective. You will know if the burner switch is the likely culprit after troubleshooting the likely causes above.

Depending on the type of stove, the defective switch may need to be replaced by removing the rear panel.

Read More: