Each brand of appliance has specific error codes that should be learned in advance. In the event that you cannot find your owner’s manual, we can run through the error codes for your Whirlpool duet washer.

Whirlpool Duet Washer Error Codes: Before You Start

It’s nice to have the ability to view past error codes on the Whirlpool Duet washer once they’ve been cleared. It is therefore possible to check all the codes thrown out if more than one was thrown out.

Your Whirlpool duet washer must first be put into diagnostic mode before you can do this. All buttons except start, power, and cancel can be pressed to accomplish this. In eight seconds, you must press those buttons nine times in succession. If the button is pressed fast enough, the word “888” will appear on the screen.

A Whirlpool duet washer error code can be viewed if you press the first and third buttons simultaneously. Make a note of them so you can check them later to see what has been happening.

There are a number of error codes on Whirlpool Duet washer

You need to know what your Whirlpool Duet washer’s error codes mean now that you know how to find them. All error codes will point you in the right direction, but some are more specific than others.

Whirlpool Duet Washer Error Codes:

Whirlpool SUDS Error

You probably don’t need this if your washer throws this error. The suds are probably visible inside the drum. White vinegar can help drain these, but they are difficult to drain. You should ensure that the detergent you are using is the right kind for your washer if you are using too much. The drain pump or pressure switch may be malfunctioning if that is not the case.

Whirlpool FoE1 Error

The problem is probably caused by pressing the wrong button. The washer was on a clean cycle when items were detected inside.

Whirlpool F1E1 Error

An error has occurred in the main control. In most cases, it indicates a malfunction in the main control board. It may be necessary to unplug the washer and wait for it to reset if there is a real problem.

Whirlpool F1E2 Error

If the control board has not been reset after you have tried resetting it several times, this message will appear.

Whirlpool F2E3 Error

The number of instances of this error is not very high. A malfunction like this rarely happens when a connection to the control board fails to select a wash cycle.

Whirlpool F3E1 Error

When these type of Whirlpool duet washer error codes appears, the pressure switch has a problem, and instead of replacing it immediately, you should check it for blockages.

Whirlpool F3E2 Error

A washer will display this error when the temperature is higher or lower than the ideal range for the cycle. Make sure the temperature sensor is still working and connected with a multimeter.

Whirlpool F5E1 Error

There may be a problem with the door switch or the wash door may be open at the beginning of the cycle if the error code indicates a problem with the door switch. The same thing can also be seen if you run three cycles without opening the door at all during that period of time.

Whirlpool F5E2 Error

If you try to lock the door of your washer six times, then the error code will appear on the screen. In some cases, re-aligning a lock may be necessary if it has been broken or malfunctioning.

Whirlpool F5E3 Error

Again, the washer will attempt to unlock the door six times before displaying this error message.

Whirlpool F6E2 Error

The motor control board and the control board have a problem communicating, resulting in this error. Usually, the wire connections need to be checked, but it could also be a problem with either part.

Whirlpool F7E2 Error

A motor fault is indicated by this condition. Ensure that the drum is free to turn. Alternatively, it may be the motor control board that is malfunctioning.

Whirlpool F8E1 Error

After 13 minutes of unsuccessful filling, your washer will display this error code, which is usually caused by a problem with the water inlet. Make sure the appliance is connected to water as well.

Whirlpool F8 E2 Error

There is a problem with the dispenser motor indicated by this error code. Therefore, your wash cycle will not include detergent.

Whirlpool F8E3 Error

Your washer was very close to overfilling if you see this Whirlpool duet washer error code. In essence, it just saved you a lot of trouble by shutting down the function. Moreover, it could be a pressure sensor issue, a drain pump issue, a problem with the water fill valve, or even a problem with the control board.

Whirlpool F8E4 Error

Occasionally, this error code will appear on Whirlpool duet washers when they are having trouble filling up. In this case, the flow meter appears to be malfunctioning.

Whirlpool F9E1 Error

There was a problem draining the washer too quickly during the cycle, which causes Whirlpool Duet washers to display this error code most of the time. If there is still standing water, you may have a clog somewhere or a malfunctioning drain pump.

Clear Stored Whirlpool Duet Washer Error & Fault Codes

It is not always possible to clear error code memory on Whirlpool duet washers. However, after entering the Whirlpool Duet washer’s diagnostic mode and recording any error codes, the style does. As if nothing ever happened, hold the 3rd button used for diagnostics for five seconds.

Read More:

The post Whirlpool Duet Washer Error Codes – Troubleshooting Guide [2022] appeared first on My Universal Remote Tips And Codes.